Technical Parameters
Ø Working Pressure:16 Bar (For Air Blown Fiber System)
Ø Working Temperature: -20℃~+50℃
Ø Fluid: Compressed Air
Ø Lifespan:20 Years
Ø Standards: EN50411-2-8
Material
Ø Body: Polycarbonate
Ø Seal: NBR
Ø Washer: Polyacetal
Ø Lock Claws: SUS
Ø Collar: Polyacetal
Ø Sleeve: Polyacetal
Notes
Ø Please confirm the microduct outer diameter whether has damaged or scratches, connection face must be clean.
Ø Please confirm the microduct outer diameter nominal tolerances meets±0.1 mm.
Ø Please make sure the connection micro duct end face is cut into rectangular plane.
Ø Please confirm the microduct should be through the sealing ring, have been pushed to the end of the joint, until it couldn't go far again.
Ø After connecting the microducts, must check whether the duct can pull, then put into use.
Ø When disassemble the microducts, please make sure the pressure is 0.
Description
Ø Connect two microducts which are the same outer diameter
Ø Easy installation, without any special tools
Ø Transparent plastic body, easy to observe the situation
Ø High temperature resistance -40℃ ~65℃
Ø High pressure resistance>25bar
Ø Standard EN50411-2-8
v FR Resistance styles also available
Specification | Duct OD/ID (mm) | PCS/CTN |
KPSTR3/2.1 | 3/2.1 | 5000 |
KPSTR4/2.5 | 4/2.5 | 3000 |
KPSTR5/2.1 | 5/2.1 | 3000 |
KPSTR5/3.5 | 5/3.5 | 3000 |
KPSTR6/4 | 6/4 | 3000 |
KPSTR7/3.5 | 7/3.5 | 2000 |
KPSTR7/4 | 7/4 | 2000 |
KPSTR7/5.5 | 7/5.5 | 2000 |
KPSTR8/3.5 | 8/3.5 | 2000 |
KPSTR8/5 | 8/5 | 2000 |
KPSTR8/6 | 8/6 | 2000 |
KPSTR8.5/6 | 8.5/6 | 2000 |
KPSTR10/6 | 10/6 | 1000 |
KPSTR10/8 | 10/8 | 1000 |
KPSTR12/8 | 12/8 | 1000 |
KPSTR12/9 | 12/9 | 1000 |
KPSTR12/10 | 12/10 | 1000 |
KPSTR12.7/10 | 12.7/10 | 1000 |
KPSTR14/10 | 14/10 | 800 |
KPSTR14/12 | 14/12 | 800 |
KPSTR15/12 | 15/12 | 800 |
KPSTR16/12 | 16/12 | 600 |
KPSTR16/13 | 16/13 | 600 |
KPSTR18/12 | 18/12 | 400 |
KPSTR18/14 | 18/14 | 400 |
Technical Parameters
Ø Working Pressure:16 Bar (For Air Blown Fiber System)
Ø Working Temperature: -20℃~+50℃
Ø Fluid: Compressed Air
Ø Lifespan:20 Years
Ø Standards: EN50411-2-8
Material
Ø Body: Polycarbonate
Ø Seal: NBR
Ø Washer: Polyacetal
Ø Lock Claws: SUS
Ø Collar: Polyacetal
Ø Sleeve: Polyacetal
Notes
Ø Please confirm the microduct outer diameter whether has damaged or scratches, connection face must be clean.
Ø Please confirm the microduct outer diameter nominal tolerances meets±0.1 mm.
Ø Please make sure the connection micro duct end face is cut into rectangular plane.
Ø Please confirm the microduct should be through the sealing ring, have been pushed to the end of the joint, until it couldn't go far again.
Ø After connecting the microducts, must check whether the duct can pull, then put into use.
Ø When disassemble the microducts, please make sure the pressure is 0.
Description
Ø Connect two microducts which are the same outer diameter
Ø Easy installation, without any special tools
Ø Transparent plastic body, easy to observe the situation
Ø High temperature resistance -40℃ ~65℃
Ø High pressure resistance>25bar
Ø Standard EN50411-2-8
v FR Resistance styles also available
Specification | Duct OD/ID (mm) | PCS/CTN |
KPSTR3/2.1 | 3/2.1 | 5000 |
KPSTR4/2.5 | 4/2.5 | 3000 |
KPSTR5/2.1 | 5/2.1 | 3000 |
KPSTR5/3.5 | 5/3.5 | 3000 |
KPSTR6/4 | 6/4 | 3000 |
KPSTR7/3.5 | 7/3.5 | 2000 |
KPSTR7/4 | 7/4 | 2000 |
KPSTR7/5.5 | 7/5.5 | 2000 |
KPSTR8/3.5 | 8/3.5 | 2000 |
KPSTR8/5 | 8/5 | 2000 |
KPSTR8/6 | 8/6 | 2000 |
KPSTR8.5/6 | 8.5/6 | 2000 |
KPSTR10/6 | 10/6 | 1000 |
KPSTR10/8 | 10/8 | 1000 |
KPSTR12/8 | 12/8 | 1000 |
KPSTR12/9 | 12/9 | 1000 |
KPSTR12/10 | 12/10 | 1000 |
KPSTR12.7/10 | 12.7/10 | 1000 |
KPSTR14/10 | 14/10 | 800 |
KPSTR14/12 | 14/12 | 800 |
KPSTR15/12 | 15/12 | 800 |
KPSTR16/12 | 16/12 | 600 |
KPSTR16/13 | 16/13 | 600 |
KPSTR18/12 | 18/12 | 400 |
KPSTR18/14 | 18/14 | 400 |