 |
| Quantity: | |
|---|---|
Technical Parameters
Ø Working Pressure:16 Bar (For Air Blown Fiber System)
Ø Working Temperature: -20℃~+50℃
Ø Fluid: Compressed Air
Ø Lifespan:20 Years
Ø 
Standards: EN50411-2-8
Material
Ø Body: Polycarbonate
Ø Seal: NBR
Ø Washer: Polyacetal
Ø Lock Claws: SUS
Ø Collar: Polyacetal
Ø Sleeve: Polyacetal
Notes
Ø Please confirm the microduct outer diameter whether has damaged or scratches, connection face must be clean.
Ø Please confirm the microduct outer diameter nominal tolerances meets±0.1 mm.
Ø Please make sure the connection micro duct end face is cut into rectangular plane.
Ø Please confirm the microduct should be through the sealing ring, have been pushed to the end of the joint, until it couldn't go far again.
Ø After connecting the microducts, must check whether the duct can pull, then put into use.
Ø When disassemble the microducts, please make sure the pressure is 0.
Description
Ø Easy installation, without any special tools
Ø Transparent plastic body, easy to observe the situation.
Ø High temperature resistance -40℃~65℃
Ø Avoid fluid (gas) entering the microducts and damage the equipment’s
Specification | Duct OD (mm) | Cable Range(mm) | PCS/CTN |
KPLBK5/2.5 | 5 | 0.9-2.5 | 2000 |
KPLBK7/4.5 | 7 | 0.9-4.5 | 1000 |
KPLBK8/4.5 | 8 | 0.9-4.5 | 1000 |
KPLBK10/6 | 10 | 3-6 | 1000 |
KPLBK10/8 | 10 | 5-8 | 1000 |
KPLBK12/6 | 12 | 3-6 | 600 |
KPLBK12/8 | 12 | 5-8 | 600 |
KPLBK14/6 | 14 | 3-6 | 400 |
KPLBK14/8 | 14 | 5-8 | 400 |
KPLBK14/10 | 14 | 7-10 | 400 |
KPLBK16/6 | 16 | 3-6 | 400 |
KPLBK16/8 | 16 | 5-8 | 400 |
KPLBK16/10 | 16 | 7-10 | 400 |
KPLBK18/8 | 18 | 5-8 | 300 |
KPLBK18/10 | 18 | 7-10 | 300 |
KPLBK18/12 | 18 | 9-12 | 300 |
Technical Parameters
Ø Working Pressure:16 Bar (For Air Blown Fiber System)
Ø Working Temperature: -20℃~+50℃
Ø Fluid: Compressed Air
Ø Lifespan:20 Years
Ø Standards: EN50411-2-8
Material
Ø Body: Polycarbonate
Ø Seal: NBR
Ø Washer: Polyacetal
Ø Lock Claws: SUS
Ø Collar: Polyacetal
Ø Sleeve: Polyacetal
Notes
Ø Please confirm the microduct outer diameter whether has damaged or scratches, connection face must be clean.
Ø Please confirm the microduct outer diameter nominal tolerances meets±0.1 mm.
Ø Please make sure the connection micro duct end face is cut into rectangular plane.
Ø Please confirm the microduct should be through the sealing ring, have been pushed to the end of the joint, until it couldn't go far again.
Ø After connecting the microducts, must check whether the duct can pull, then put into use.
Ø When disassemble the microducts, please make sure the pressure is 0.
Description
Ø Easy installation, without any special tools
Ø Transparent plastic body, easy to observe the situation.
Ø High temperature resistance -40℃~65℃
Ø Avoid fluid (gas) entering the microducts and damage the equipment’s
Specification | Duct OD (mm) | Cable Range(mm) | PCS/CTN |
KPLBK5/2.5 | 5 | 0.9-2.5 | 2000 |
KPLBK7/4.5 | 7 | 0.9-4.5 | 1000 |
KPLBK8/4.5 | 8 | 0.9-4.5 | 1000 |
KPLBK10/6 | 10 | 3-6 | 1000 |
KPLBK10/8 | 10 | 5-8 | 1000 |
KPLBK12/6 | 12 | 3-6 | 600 |
KPLBK12/8 | 12 | 5-8 | 600 |
KPLBK14/6 | 14 | 3-6 | 400 |
KPLBK14/8 | 14 | 5-8 | 400 |
KPLBK14/10 | 14 | 7-10 | 400 |
KPLBK16/6 | 16 | 3-6 | 400 |
KPLBK16/8 | 16 | 5-8 | 400 |
KPLBK16/10 | 16 | 7-10 | 400 |
KPLBK18/8 | 18 | 5-8 | 300 |
KPLBK18/10 | 18 | 7-10 | 300 |
KPLBK18/12 | 18 | 9-12 | 300 |
